Skip to main content

10 Things I learnt about Arkansas Stones

10 things I learned about Arkansas stones

Stones should be kept in their own box, or in a segregated box. This keeps out saw dust, and protects from stones knocking on each other, causing chips.

1)  Not for sharpening tools:
Not a typing error too.
I'm sure everyone has a dull knife or two in the kitchen. The type that will not cut meat or slice bread. You may be able to push-cut an apple, but that's all it'll do. Or that vintage ebay Marples chisel or that plane iron off a vintage Bailey. The edges on these tools will need to be dressed (chips ground-out, skew-edge squared, rolled-edge removed) and re-profiled (irregular and multiple bevel angles corrected) on a bench grinder or a coarse diamond plate, carborundum stones etc.

All the above before it even touches an Arkansas stone. I have never met an Arkansas stone that can remove chips or correct bevel in less than 2 hours.

Use Arkansas stones for honing and polishing. Old timers call it whetting. These processes, along with dressing and grinding, forms part of sharpening, but what I'm saying is this: Do not start with Arkansas, unless the edge is still quite sharp and just needs a touch up.


2)    Same name, different rock,
and sometimes, same rock, different names. Frequently, the dude who sell you the stone do not know much about it, let alone using it.
 
3)    Water will work, but oil is easier to use.
For one, it penetrates the stone better, forming a swarf resistant barrier that would otherwise glaze and clog your stone’s surface. Water tends to bead up at the slightest hint of oil, and a water lubricated stone dry out faster. If you really must use water, add a few drops of dish washing detergent. It improves the wetting effect drastically.



Here I'm using a worn cheap diamond plate to dress a Translucent before I start to sharpen. I purchased this from "Halls Pro-edge". Being a "seconds" it has minor discoloration and fault lines, but it cuts just as well as my Norton equivalent, but at a fraction of the usual price. My favourite go-to stone for touch ups.

4)    You can speed up your stone.
If you rub a diamond encrusted plate lubricated with oil prior to sharpening, it does 3 things:
 
a)    Slurry formed aids sharpening. A slurried stone cuts faster. It behaves like a friable water stone.
 
b)    To a lesser extent, you flatten the stone a little.
 
c)    The scratch pattern is somewhat more pronounced, leveling off as the slurry gets processed and flushed out by oil added.
Freshly dressed Translucent, ready to go..

5)    Change the grit without changing the stone?
To touch up a chisel, I sometimes rub a piece of carborundum stone onto an oily Washita stone, and I use the slurry to kick start my sharpening on my Arkansas stones. 

A washita will benefit from a few quick rubs from a Silicon Carbide. It also flattens the stone, to a lesser extent.

We all know that carborundums are fast cutting soft stones, and using it on a slightly dull but perfectly symmetrical tool may do more bad than good on a chisel that is merely in need of a touch up. The next best thing is to impart the aggressive cutting silicon carbide crystals to your gentle but flat Arkansas stone.As you move up to your harder and finer stones, use a Washita to impart an oily slurry on your translucent stone, and so on, flushing out the slurry as you finish. 
A frequently "rubbed" stone will stick. Surgical Black Arkansas with a similar rubbing stone. I reserve this stone for times when I feel very vain and have an inexplicable need to over dress a chisel I intend to put away for a while.

Black surgical slurry on black surgical stone seems to “aid” a usually slow finishing process. Now you know why some woodworkers add diamond paste. (A word about such paste: unlike silicon carbides in carborundum, which are easily flushed out, diamond paste can be quite persistently embedded in your stone, so choose an appropriate grit)

6)    The longer the stone, the lesser the stroke. Six to eight inches by two inch wide stones seems to work well for me.

7)    Again, you can alter the grit of the stone simply by using oils of differing viscosity (you can thin-out mineral oil with kerosene) If you pour kerosene on a coarse stone, it gets absorbed too fast into the stone. Adjust your cutting fluid just thick enough so that a film stays on your stone for many strokes, but not so thick that it forms a barrier that impedes the sharpening action. Experiment.
 
8)    Any oil is better than no oil. Olive oil will turn rancid and gum up, clogging the pores. (They work, at least on a short term) Grape seed oil, camellia oil(expensive), clove oil, baby oil (works well if you do not mind the baby smell), mineral oil, 3-in-1 light machinery oil, WD40 (these may leave a yellow residue on your white stones)

Petroleum Jelly( VASELINE ) works great for tempering Carborundums that cuts too aggressively or does not retain lube film well on the surface) The best oils to use are non-drying oils, and preferably colorless and odorless.

9)    Check your stone for flatness:
Washitas and soft Arkansas do get hollowed by uneven use.They are not much of an issue if you are doing a kitchen knife, or the bevel of a chisel. The back of an chisel or plane iron will be "bellied" on a hollowed stone, making burr removal ineffective on subsequent stones.
 
10)   My stone is not cutting..
If you are applying more pressure or putting in more strokes than what feels right, your stone is not cutting(diamond-plate!), or you’re using too fine a grit. You are wasting your time. 20 to 200 strokes per stone feel healthy to me. You need to strike a balance between speed and fineness of edge. Obviously, we do not need to polish a scrub or jack plane iron the way we finish a smoothing plane iron or straight razor.


So much for my theory. Nobody said you cannot grind out an edge on a grinder, on  sheet glass-backed 80 grit sandpaper, or on carborundum stones, then sharpen and hone on your Arkansas, and  finally strop on leather. The only rule governing stones is to use what works for you. I’ve seen folks sharpening jack knives on cinder blocks and honing on bricks. That guy then proceeds to shave his leg. The idea is to know who you are: A handtool user seeking the most efficient way, an old school hand tool purist (little regard for cost or time), or a revolutionary trying to prove a point. Then you will know what you need.

When I was still playing with waterstones, namely Japanese synthetic stones, the slurry that gets left behind after the water bucket has dried up are saved. These are probably Aluminium Oxide particles. I use this powder as a boost to my Washita, when I want to speed things up a bit. I mix in a pinch with some mineral oil on the stone surface. This is similar to using a Japanese flattening plate called "Kanaban"
Woodworkers in Japan will flatten the blades of their plane on a mild steel plate encrusted with bits of silicon carbide.

I do not think what I've just described is anything new or innovative. I would love to hear what you use for your sharpening needs.

Comments

Popular posts from this blog

SHARPENING WITH ARKANSAS STONES

What on earth are they? A user made box of assorted Arkansas stones. They are America's answer to: The Wales' Welsh Slate (Dragon's Tongue); The Scotch Tam O'Shanter; The English Charnley Forest stone; The Japanese Tenin Toishi; The German Thuringian Hone; The Chinese Guangzhou River bedrock; The Belgian Coticule; You get the idea. Local rocks that you use to sharpen mama's kitchen knives.   A collection of smaller pocket-sized Arkansas stones  In this entry, I will not try to tell you what you probably already know. What is the point of describing that oily rock you already have under your bench, in your drawer, in a can of kerosene? Note also, that the sharpening I describe here is best applied to woodworking in general. I am an amateur handtool woodworker. Sharpening a straight razor would be entirely another branch of science. I do not profess to know all there is to know about sharpening or Arkansas stones; I simply failed

The prolific & seemingly mundane Stanley 110 block plane..

R eally?   Well, it's everywhere, check Granpa or uncle Tim's shack ( if you include copies of it by lesser tool makers) For something so abundant (well, Stanley sold them by truckloads), so common and so relatively inexpensive, I will attempt to wax some lyrical on them. By "them" I mean their design, their construction. The plane pictured above was purchased off ebay for $4.90. It looked like Joe Meatball (to borrow Patrick Leach's character) bought it, used it on some hardwood (pre silicon valley micro chipping at the edge)without first fettling the plane(unsharpened factory bevel), and put it away (in some dry place), and totally forgot about it. First off, at Five Bucks, how can you go wrong? Five bucks don't buy you a door wedge these days.   STANLEY'S SUPERIOR ADJUSTABLE HEIGHT DOOR WEDGE, TYPE 16.  1) The lever cap also serves as an ergonomic palm-rest to push the plane forward, and the oval shaped  cut-out serves as a hanging h

An Essential Pocket Knife : The Stockman

You're so right. I should be writing about Whittlers instead of Stockman knives. Afterall, this is a wood working blog. But do you whittle the whole day? Perhaps. Can you peel an apple with a whittler? Maybe, but not as well. What if you forgot the butter knife at a picnic, or you somehow need to spey or neuter an animal in an instant?.. (ok, I'm pulling your leg, but I'm referring to the ubiquitous spey blade in your stockman.) A stockman knife (Also called your Gandpa's EDC) will do all of the above with ease, and it will WHITTLE. My shallow pocket and minute brain says that Whittlers are for collectors. Try buying a Stag handled split-backsping whittler. They are not cheap. This is one of the forty stockmen I've purchased online. The other 39 are on their way. And yes, I have issues. The stockman bug maybe. Wait till my wife sees them: I like to imagine myself as a craftsman first, woodworker second. Now you see why I bought this brand. Looks so